MOTOR DRIVERS, STEPPER MOTOR DRIVER
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry PiMOTOR DRIVERS, STEPPER MOTOR DRIVER
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
boards, MOTOR DRIVERS, MOTORS
5V-12V DC Brushless Driver Board Controller For Hard Drive Motor 3/4 Wire
E-BIKE MOTOR CONTROLLER, MOTOR DRIVERS
6V 12V 24V 8A PWM DC Motor Speed Controller CCM5D Digital Display LED Motor Controller Speed RegulatorE-BIKE MOTOR CONTROLLER, MOTOR DRIVERS
6V 12V 24V 8A PWM DC Motor Speed Controller CCM5D Digital Display LED Motor Controller Speed Regulator
Input Supply Voltage (V) 6V-30VDC Max. Continuous Current (A) Rated current 5A (8A MAX, cannot be prolonged) Maximum Output Power 240W LED display the duty ratio 0-100% PWM Frequency (KHz) 16 Duty Cycle adjustable 0%-100% Dimensions (LxWxH) 78*42*25mmSKU: n/a
COMPONENTS, ROBOT PARTS
DIY 3DOF 3-AXIS CONTROL PALLETIZING ROBOT ARM MODEL WITH SERVO ARM PLATE (NOT INCLUDING MG995 SERVO)COMPONENTS, ROBOT PARTS
DIY 3DOF 3-AXIS CONTROL PALLETIZING ROBOT ARM MODEL WITH SERVO ARM PLATE (NOT INCLUDING MG995 SERVO)
1. 3-DOF manipulator! Vertical arm up and down, back and forth.
2. U-type robot waist bracket on the arm can be mounted directly on the base in the car or any other desktop platform.
3. The vehicle type 3-DOF manipulator medium length, back and forth up and down, in which a mechanical claw opening and closing of the steering gear control, two servo control arm up and down back and forth.
4. This robot is particularly suitable as a vehicle manipulator robot car, grab the ball, catch the car are particularly good, very suitable for their own DIY or robotic smart car racing.
5. Activities can use 180 degree steering joints.SKU: n/a
MOTOR DRIVERS, MOTORS
E3D Nema17 Single Shaft 0.9 Degree Compact Powerful Stepper Motor + Motor Bracket
COMPONENTS, RC SERVO MOTOR
EMAX BLHELI 12AMP ESC FOR QUADCOPTER / DRONES
Based on BL Heli firmware.
Includes low voltage protection, over heat protection, and self-check functions.
Separate power supply for MCU and BEC, helping eliminate magnetic interference.
Fully programmable by any standard programming card or directly from your transmitter.
Customisable throttle range.
Built in linear or switched BEC.
Cont Current: 12A
Burst Current: 15A
BEC Mode: Linear BEC : 5v / 1A
Lipo Cells: 2-4
Weight: 11g including wires
Size: 42x20x8mmSKU: n/a
IoT and Wireless, MOTOR DRIVERS, WIRELESS SERIAL MODULES
L293D Motor Driver Board for ESP8266 WiFi NodeMcu Lua ESP12EIoT and Wireless, MOTOR DRIVERS, WIRELESS SERIAL MODULES
L293D Motor Driver Board for ESP8266 WiFi NodeMcu Lua ESP12E
- Motor Power Range: 4.5V ~ 36V
- Control supply range: 4.5V ~ 9V
- Logical operating current Iss: ≤60mA
- Driving part of the work current Io: ≤1.2A
- Maximum power dissipation: 4W (T = 90 ℃)
- Operating temperature : -25 ℃ ~ + 125 ℃
- Drive Type: Dual high-power H-bridge driver
MODULE, MOTOR DRIVERS
L293D Motor Driver Module
- The driver two holes of 3 mm dia.
- Male burg-stick connectors for supply, ground and input connection.
- Screw terminal connectors for easy motor connection.
- High noise immunity inputs.
- Operating Voltage(VDC): 4.5 to 12
- Peak Current (A): 600 mA
- No. of Channels: 1
COMPONENTS, ROBOT PARTS
MINI OSD W/ KV TEAM MOD FOR RACING F3 NAZE32 FLIGHT CONTROLLER RC DRONE
NO DC/DC converter, power board via 5 volts
FTDI cable compatible pinout
Standard 6-pin ISP header
Two LED indicators
ATmega328P with Arduino bootloader
MAX7456 monochrome on-screen display
16 x 16mm Size
Pad for an Analog or Digital PWM RSSI signal
Pad for the connection of a Current Sensor
ATmega328P with Arduino bootloader
Standalone, or with APM / Flip / Flip32+ flight controllers
These modifications allow direct connection of two batteries (up to 4S)
This hardware take the hardware mods for this firmware, and builds them into an RTF solution.
This Board can be used just as a normal OSD for APM or it can be used with MWC KV Team Mod.
Two independent power sections with an LED indicator on each.
Solder jumpers for combining the power sections
Solder jumper for PAL video option
+5V 500mA regulator for up to +12V supply input
Exposed test points for HSYNC and LOSSKU: n/a
Stepper Motor Driver Leadshine DM542 Digital
- Good high-speed performance
- Supply voltage up to +50VDC
- Output current up to 4.2A
- Pulse frequency up to 300 KHz
- Automatic idle-current reduction
- 3-state current control technology
- Self-adjustment technology
- Pure-sinusoidal current control technology
ARDUINO, COMPONENTS, ELECTRONICS, MODULE, PROGRAMMERS
USB To 3.5mm Mic and Headphone Jack Stereo Headset Audio Adapter USB Sound Card 7.1ARDUINO, COMPONENTS, ELECTRONICS, MODULE, PROGRAMMERS
USB To 3.5mm Mic and Headphone Jack Stereo Headset Audio Adapter USB Sound Card 7.1
- One male USB plug
- Two 3.5mm (3-position) Female Jacks (1 for the mic, 1 for headset)
- Specifically for mic-capable headphones
- Convenient tangle-free flat cable design
- Allows the use of older audio accessories with newer computers
- Can be used with any device which uses USB portable devices
3D Printers, COMPONENTS, ELECTRONICS
3d Printer 128 64 Smart Lcd Controller for Ramps 1.4-3
- RAMPS 1.4 LCD12864 intelligent controller
- LED background light control circuit
- LED background light control circuit, a small function of intelligent controller, With pin short time to decide on all LED turn or steering 30 seconds
- You can turn on the light time to do long or short form of the adjustment TRIMM R4100K from 10 seconds to 2 minutes